Search
Filters
Close

JetCon-2502

Industrial Ethernet over VDSL2 Extender
Caratteristiche
  • IEEE 802.3u 100Base-TX Fast Ethernet Converter
  • IEEE 802.3x Flow control & Back-pressure
  • ITU-T G.993.2 VDSL2 standard
  • 2 x RJ-11 connectors for POTS/ISDN and VDSL 2
  • 1 x RJ-45 10/100Mbps Fast Ethernet Port
  • Built-in POTS/ISDN Splitter
  • Extends Voice and Ethernet distance to 1KM
  • Transparent 1792 bytes packet size
  • QoS with broadcast packet filtering for data precedence
  • DC 12~48V Power input by power jack and terminal block
  • Supports AC 1.5KV Hi-Pot isolation protection
  • Operating temperature -40°~70°C
Manufacturer: Korenix Technology
Technology
Standard
IEEE 802.3 10 Base-T
IEEE 802.3u 100 Base-TX
IEEE 802.1p Class of Service
IEEE 802.1Q Quality of Service
ITU-T G.993.2 VDSL2

Performance
Forwarding Technology
Store and Forward technology with 64 ~1792 bytes packet forwarding ability
Switch Packet Buffer
384Kbits
Mac Table
2K with 300 Sec agent time
Class of Service
4 Packet forwarding queues with 1 (Lowest):4 (Low):8 (High):15 (Highest) WRR (weighted round robin) forwarding schematics
Quality of Service
VLAN tag priority, IPv4 packet precedence and IPv6 ToS.
Broadcast filtering
Fast Ethernet: 200 packet / per sec. @ 100Mbps; 20 packet / per sec. @ 10Mbps

Interface
Number of Ports
1x 10/100Mbps Fast Ethernet port with Auto MDI/MDI-X function
Auto-Negotiation
1x Line for ISDN/POTS
1x VDSL2
Connectors
10/100 Base-TX: RJ-45 with auto MDI/MDI-X, Auto-Negotiation
ISDN/POTS: RJ-11
VDSL2: RJ-11
Cables
RJ-45 Fast Ethernet port: Cat.4,5, 4-pairs UTP cable, up to 100 meters
VDSL2: 1pairs of UTP cable, up to 3000 feet.
Line: Integrated ISDN/POTS
Configuration DIP Switch
DIP-1 (Mode selection): On (Master) / Off (Slave)
DIP-2 (Impulse protection):On (Interleave)/ Off (Fast);Interleave mode with less than 250ms forwarding latency, Fast mode is less than 2ms forwarding latency.
DIP-3 (Rate Control): On (Non-Symmetric )/Off (Symmetric)
DIP-4 (SNR Control): On (6dB)/ Off (9dB) 
300bps to 921.6Kbps
Diagnostic LED
System Power: Power on (Green on)
Fast Ethernet Port: Speed (100 Mbps: Yellow On), Link/Activity: Green on ( Link at 10 or 100Mbps), Green Blinking ( packet is on transmitting)
Master (Green On): Device operating under Master Mode
VDSL Link/ Negotiation (Green): On/ Link, Blinking/Negotiation

Power Requirements
System Power
DC Jack: 12~48V, Ø 2mm Center Pin
Terminal block: DC 12~48V, 3-Pin terminal block with earth ground. Power input with polarity reverse protection.
Power Consumption
5Watts @DC 24V(Maximum)

Mechanical
Installation
Wall Mount or DIN-Rail mount
Casing
Aluminum metal case
Dimensions
29mm (H) x 88mm(W) x 114mm (D)

Environmental
Operating Temperature
-40 ~ 70°C
Operating Humidity
0% ~ 95% (Non-condensing)
Storage Temperature
-40 ~ 80°C
Storage Humidity
0% ~ 95% (Non-condensing)
 
Regulatory Approvals
Hi-Pot
Ethernet port AC 1.5KV for port to power
EMI
FCC Class A; CE/EN55022 class A
EMC Immunity Interface
IEC 61000-4-2, IEC61000-4-3, IEC61000-4-4, 
IEC61000-4-5, IEC61000-4-6, IEC61000-4-8
Shock
IEC60068-2-27
Vibration
IEC60068-2-6
Free Fall
IEC60068-2-32
Technology
Standard
IEEE 802.3 10 Base-T
IEEE 802.3u 100 Base-TX
IEEE 802.1p Class of Service
IEEE 802.1Q Quality of Service
ITU-T G.993.2 VDSL2

Performance
Forwarding Technology
Store and Forward technology with 64 ~1792 bytes packet forwarding ability
Switch Packet Buffer
384Kbits
Mac Table
2K with 300 Sec agent time
Class of Service
4 Packet forwarding queues with 1 (Lowest):4 (Low):8 (High):15 (Highest) WRR (weighted round robin) forwarding schematics
Quality of Service
VLAN tag priority, IPv4 packet precedence and IPv6 ToS.
Broadcast filtering
Fast Ethernet: 200 packet / per sec. @ 100Mbps; 20 packet / per sec. @ 10Mbps

Interface
Number of Ports
1x 10/100Mbps Fast Ethernet port with Auto MDI/MDI-X function
Auto-Negotiation
1x Line for ISDN/POTS
1x VDSL2
Connectors
10/100 Base-TX: RJ-45 with auto MDI/MDI-X, Auto-Negotiation
ISDN/POTS: RJ-11
VDSL2: RJ-11
Cables
RJ-45 Fast Ethernet port: Cat.4,5, 4-pairs UTP cable, up to 100 meters
VDSL2: 1pairs of UTP cable, up to 3000 feet.
Line: Integrated ISDN/POTS
Configuration DIP Switch
DIP-1 (Mode selection): On (Master) / Off (Slave)
DIP-2 (Impulse protection):On (Interleave)/ Off (Fast);Interleave mode with less than 250ms forwarding latency, Fast mode is less than 2ms forwarding latency.
DIP-3 (Rate Control): On (Non-Symmetric )/Off (Symmetric)
DIP-4 (SNR Control): On (6dB)/ Off (9dB) 
300bps to 921.6Kbps
Diagnostic LED
System Power: Power on (Green on)
Fast Ethernet Port: Speed (100 Mbps: Yellow On), Link/Activity: Green on ( Link at 10 or 100Mbps), Green Blinking ( packet is on transmitting)
Master (Green On): Device operating under Master Mode
VDSL Link/ Negotiation (Green): On/ Link, Blinking/Negotiation

Power Requirements
System Power
DC Jack: 12~48V, Ø 2mm Center Pin
Terminal block: DC 12~48V, 3-Pin terminal block with earth ground. Power input with polarity reverse protection.
Power Consumption
5Watts @DC 24V(Maximum)

Mechanical
Installation
Wall Mount or DIN-Rail mount
Casing
Aluminum metal case
Dimensions
29mm (H) x 88mm(W) x 114mm (D)

Environmental
Operating Temperature
-40 ~ 70°C
Operating Humidity
0% ~ 95% (Non-condensing)
Storage Temperature
-40 ~ 80°C
Storage Humidity
0% ~ 95% (Non-condensing)
 
Regulatory Approvals
Hi-Pot
Ethernet port AC 1.5KV for port to power
EMI
FCC Class A; CE/EN55022 class A
EMC Immunity Interface
IEC 61000-4-2, IEC61000-4-3, IEC61000-4-4, 
IEC61000-4-5, IEC61000-4-6, IEC61000-4-8
Shock
IEC60068-2-27
Vibration
IEC60068-2-6
Free Fall
IEC60068-2-32